MagForce motor system installation: Difference between revisions

Line 202:

Make a record of the following settings for future reference when setup is complete:

*Bell Number (1 is the largest bell)

;Bell Number

*Swing Angle ~~(intended~~ angle)

: 1 is the largest bell

*Transmission ~~(rotary~~ code wheel to angle ratio - always 5.0 for proximity sensors)

*%Start ~~(portion~~ of swing angle for starting pulses)

;Dimensions

*%Brake ~~(portion~~ of swing angle of braking pulses)

: Air gap between motor and reactor plate (typically 1/4 to 3/8 inch)

*1Oscillation ~~(period~~ in milliseconds for one complete swing cycle at 20 degrees of amplitude for proximity sensor calibration)

: Center of bearing spindle to center of motor

*Pos Option - not used

*PowerStaSwi ~~(power~~ reduction using soft-start current limiting 1-8, 9=full inrush current)

;Swing Angle

*Power Brake 1 (> 20 ~~deg, first brake~~ current limit 1-8)

: Intended swinging amplitude angle in degrees

*Power Brake 2 (<20 ~~deg, second brake~~ current limit 1-8)

;Transmission

*StartImp ~~(maximum~~ number of impulses allowed before home sensor ~~provides~~ motion feedback)

: Rotary code wheel to angle ratio

*XtrBrakeImp ~~(extra~~ brake impulses after home sensor no longer provides motion feedback)

: ''always set to 5.0'' for proximity sensors

*MaxAmpl ~~(maximum~~ angle before ~~error and~~ shutdown)

;%Start

*P-Regulator (Proportional regulation factor)

: Percentage of swing angle for starting pulses

*I-Regulator (Integration regulation factor ~~- will be zero~~ when parameters ~~are~~ calculated and saved)

;%Brake

*Pos-Impulse (Position of the motor impulse in the sweep of the bell; 0=home 100=turnaround): Always 0 for MagForce

: Percentage of swing angle for braking pulses

*Assymmetric (Proportion of motor pulse for forward/backward balance; 50 = equal, 100 or 0 = unidirectional drive)

;1Oscillation

: Period in milliseconds for one complete swing cycle at 20 degrees of amplitude for proximity sensor calibration

: Reset value is 900, may be less for very small bells, usually higher for most bells

;Pos Option - not used

;PowerStaSwi

: Power reduction using soft-start current limiting 1-8

: 9=full inrush current which may trip circuit breaker

;Power Brake 1

: First brake at amplitudes > 20 degrees current limit 1-8

;Power Brake 2

: Secondary braking at amplitudes < 20 degrees current limit 1-8

;StartImp

: Maximum number of impulses allowed before home sensor begins to provide motion feedback

: If no feedback is received after this number of tries, the system will go into safety shutdown

;XtrBrakeImp

: Extra brake impulses after home sensor no longer provides motion feedback

: ''Should be 0'' as blind braking is not advised

;MaxAmpl

: Maximum swinging angle before safety shutdown

: ''Set to 90'' if no obstacles are in the way of the bell swinging high

;P-Regulator

: Proportional regulation factor

;I-Regulator

: Integration regulation factor

: Zero on the terminal when parameters have been successfully calculated and saved

;Pos-Impulse

: Position of the motor impulse in the sweep of the bell

: 0 = home, 100 = turnaround

: ''Always set to 0 for MagForce''

;Assymmetric

: Proportion of motor pulse for forward/backward balance

: 50 = equal pulses, 100 or 0 = unidirectional drive forward or back

== After setup complete ==

@@ Line 202: / Line 202: @@
 Make a record of the following settings for future reference when setup is complete:
-*Bell Number (1 is the largest bell)
+;Bell Number
-*Swing Angle (intended angle)
+: 1 is the largest bell
-*Transmission (rotary code wheel to angle ratio - always 5.0 for proximity sensors)
-*%Start (portion of swing angle for starting pulses)
+;Dimensions
-*%Brake (portion of swing angle of braking pulses)
+: Air gap between motor and reactor plate (typically 1/4 to 3/8 inch)
-*1Oscillation (period in milliseconds for one complete swing cycle at 20 degrees of amplitude for proximity sensor calibration)
+: Center of bearing spindle to center of motor
-*Pos Option - not used
-*PowerStaSwi (power reduction using soft-start current limiting 1-8, 9=full inrush current)
+;Swing Angle
-*Power Brake 1 (> 20 deg, first brake current limit 1-8)
+: Intended swinging amplitude angle in degrees
-*Power Brake 2 (<20 deg, second brake current limit 1-8)
+;Transmission
-*StartImp (maximum number of impulses allowed before home sensor provides motion feedback)
+: Rotary code wheel to angle ratio
-*XtrBrakeImp (extra brake impulses after home sensor no longer provides motion feedback)
+: ''always set to 5.0'' for proximity sensors
-*MaxAmpl (maximum angle before error and shutdown)
+;%Start
-*P-Regulator (Proportional regulation factor)
+: Percentage of swing angle for starting pulses
-*I-Regulator (Integration regulation factor - will be zero when parameters are calculated and saved)
+;%Brake
-*Pos-Impulse (Position of the motor impulse in the sweep of the bell; 0=home 100=turnaround): Always 0 for MagForce
+: Percentage of swing angle for braking pulses
-*Assymmetric (Proportion of motor pulse for forward/backward balance; 50 = equal, 100 or 0 = unidirectional drive)
+;1Oscillation
+: Period in milliseconds for one complete swing cycle at 20 degrees of amplitude for proximity sensor calibration
+: Reset value is 900, may be less for very small bells, usually higher for most bells
+;Pos Option - not used
+;PowerStaSwi
+: Power reduction using soft-start current limiting 1-8
+: 9=full inrush current which may trip circuit breaker
+;Power Brake 1
+: First brake at amplitudes > 20 degrees current limit 1-8
+;Power Brake 2
+: Secondary braking at amplitudes < 20 degrees current limit 1-8
+;StartImp
+: Maximum number of impulses allowed before home sensor begins to provide motion feedback
+: If no feedback is received after this number of tries, the system will go into safety shutdown
+;XtrBrakeImp
+: Extra brake impulses after home sensor no longer provides motion feedback
+: ''Should be 0'' as blind braking is not advised
+;MaxAmpl
+: Maximum swinging angle before safety shutdown
+: ''Set to 90'' if no obstacles are in the way of the bell swinging high
+;P-Regulator
+: Proportional regulation factor
+;I-Regulator
+: Integration regulation factor
+: Zero on the terminal when parameters have been successfully calculated and saved
+;Pos-Impulse
+: Position of the motor impulse in the sweep of the bell
+: 0 = home, 100 = turnaround
+: ''Always set to 0 for MagForce''
+;Assymmetric
+: Proportion of motor pulse for forward/backward balance
+: 50 = equal pulses, 100 or 0 = unidirectional drive forward or back
 == After setup complete ==