IntelliSwing 2052 motor installation: Difference between revisions
Motor winding connections corrections |
m Daveallen moved page IntelliSwing 2052 Motor hookup to IntelliSwing 2052 motor installation |
||
| (4 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
<div style="font-size:84%">'''[http://www.ChimeMaster.com Home] > [[Chime_Master_Help|Help]] > [[Installation_documentation|Installation]] '''</div><br /> | <div style="font-size:84%">'''[http://www.ChimeMaster.com Home] > [[Chime_Master_Help|Help]] > [[Installation_documentation|Installation]] '''</div><br /> | ||
== PDF Diagrams == | == PDF Diagrams == | ||
[[File:2052-jb-ccw.png|thumb|Counter-Clockwise wiring]] | |||
Click to open in your browser or right click to save link (download): | |||
* [[Media:2052MotorWiring.pdf|intelliSwing 2052 motor hookup (PDF)]] | |||
* [[Media:2052MotorInstallation.pdf|intelliSwing 2052 motor installation overview (PDF)]] | |||
* [[Media:2052MotorWiring.pdf|intelliSwing 2052 motor hookup (PDF | * [[Media:ChainStud.pdf|intelliSwing 2052 chain bracket detail (PDF)]] | ||
* [[Media:2052MotorInstallation.pdf|intelliSwing 2052 motor installation overview (PDF | * [[Media:2052ChipInstallation.pdf|intelliSwing 2052 motor chip instructions (PDF)]] | ||
* [[Media:ChainStud.pdf|intelliSwing 2052 chain bracket detail (PDF | * [[Media:2052sch.pdf|intelliSwing 2052 motor schematic diagram (PDF)]] | ||
* [[Media:2052ChipInstallation.pdf|intelliSwing 2052 motor chip instructions (PDF | |||
* [[Media:2052sch.pdf|intelliSwing 2052 motor schematic diagram (PDF | |||
== Theory of operation == | == Theory of operation == | ||
| Line 25: | Line 25: | ||
* Wire nut '''MA''' always has a red wire from the '''control box''' and a yellow wire from the motor windings. | * Wire nut '''MA''' always has a red wire from the '''control box''' and a yellow wire from the motor windings. | ||
* Wire nut '''MB''' always has a blue wire from the motor windings. | * Wire nut '''MB''' always has a blue wire from the motor windings and '''L2''' from the power disconnect. | ||
* Wire nut '''MC''' always has a white and an orange wire from the motor windings. | * Wire nut '''MC''' always has a white and an orange wire from the motor windings. | ||
| Line 95: | Line 95: | ||
The centrifugal switch is in the control box end of the motor. | The centrifugal switch is in the control box end of the motor. | ||
# Disconnect the wires from the control box in the junction box | # Disconnect the wires from the control box in the junction box. | ||
# Remove PCB from control box | # Remove PCB from control box. | ||
# Remove painted code | # Remove painted code disk. Older motors used plastic disks. Replace with PN 89002052 metal disk and two PN 80850624 set screws. | ||
# Remove four nuts on the standoffs holding the box on the motor | # Remove four nuts on the standoffs holding the box on the motor. | ||
# Remove the four standoffs and nuts holding the end cap on the motor | # Remove the four standoffs and nuts holding the end cap on the motor. | ||
# Cut the terminals off of the two wires going to the plastic switch bracket | # Cut the terminals off of the two wires going to the plastic switch bracket. | ||
# Use a wire nut to connect them together | # Use a wire nut to connect them together. | ||
# Use a wire tie to secure them to the switch bracket | # Use a wire tie to secure them to the switch bracket. | ||
# Reassemble motor by reversing previous steps | # Reassemble motor by reversing previous steps. | ||
# Place a <code><nowiki>C</nowiki></code> label on the control box | # Place a <code>'''<nowiki>C</nowiki>'''</code> label on the control box. | ||
[[Category:Installation]] | [[Category:Installation]] | ||
[[Category:Bell automation]] | [[Category:Bell automation]] | ||
[[Category:Troubleshooting]] | [[Category:Troubleshooting]] | ||