IntelliSwing 2052 motor installation: Difference between revisions

(2 intermediate revisions by 2 users not shown)

Line 25:

* Wire nut '''MA''' always has a red wire from the '''control box''' and a yellow wire from the motor windings.

* Wire nut '''MB''' always has a blue wire from the motor windings.

* Wire nut '''MB''' always has a blue wire from the motor windings and '''L2''' from the power disconnect.

* Wire nut '''MC''' always has a white and an orange wire from the motor windings.

Line 95:

The centrifugal switch is in the control box end of the motor.

# Disconnect the wires from the control box in the junction box

# Disconnect the wires from the control box in the junction box.

# Remove PCB from control box

# Remove PCB from control box.

# Remove painted code ~~wheel~~

# Remove painted code disk. Older motors used plastic disks. Replace with PN 89002052 metal disk and two PN 80850624 set screws.

# Remove four nuts on the standoffs holding the box on the motor

# Remove four nuts on the standoffs holding the box on the motor.

# Remove the four standoffs and nuts holding the end cap on the motor

# Remove the four standoffs and nuts holding the end cap on the motor.

# Cut the terminals off of the two wires going to the plastic switch bracket

# Cut the terminals off of the two wires going to the plastic switch bracket.

# Use a wire nut to connect them together

# Use a wire nut to connect them together.

# Use a wire tie to secure them to the switch bracket

# Use a wire tie to secure them to the switch bracket.

# Reassemble motor by reversing previous steps

# Reassemble motor by reversing previous steps.

# Place a <code><nowiki>C</nowiki></code> label on the control box

# Place a <code>'''<nowiki>C</nowiki>'''</code> label on the control box.

[[Category:Installation]]

[[Category:Bell automation]]

[[Category:Troubleshooting]]

@@ Line 25: / Line 25: @@
 * Wire nut '''MA''' always has a red wire from the '''control box''' and a yellow wire from the motor windings.
-* Wire nut '''MB''' always has a blue wire from the motor windings.
+* Wire nut '''MB''' always has a blue wire from the motor windings and '''L2''' from the power disconnect.
 * Wire nut '''MC''' always has a white and an orange wire from the motor windings.
@@ Line 95: / Line 95: @@
 The centrifugal switch is in the control box end of the motor.
-# Disconnect the wires from the control box in the junction box
+# Disconnect the wires from the control box in the junction box.
-# Remove PCB from control box
+# Remove PCB from control box.
-# Remove painted code wheel
+# Remove painted code disk. Older motors used plastic disks. Replace with PN 89002052 metal disk and two PN 80850624 set screws.
-# Remove four nuts on the standoffs holding the box on the motor
+# Remove four nuts on the standoffs holding the box on the motor.
-# Remove the four standoffs and nuts holding the end cap on the motor
+# Remove the four standoffs and nuts holding the end cap on the motor.
-# Cut the terminals off of the two wires going to the plastic switch bracket
+# Cut the terminals off of the two wires going to the plastic switch bracket.
-# Use a wire nut to connect them together
+# Use a wire nut to connect them together.
-# Use a wire tie to secure them to the switch bracket
+# Use a wire tie to secure them to the switch bracket.
-# Reassemble motor by reversing previous steps
+# Reassemble motor by reversing previous steps.
-# Place a <code><nowiki>C</nowiki></code> label on the control box
+# Place a <code>'''<nowiki>C</nowiki>'''</code> label on the control box.
 [[Category:Installation]]
 [[Category:Bell automation]]
 [[Category:Troubleshooting]]