Bell Control Technical Data 3700: Difference between revisions

Line 47:

Interface module

* Active - indicates the high voltage relays are enabled. Indicated from logic before drive transistor.

** Active only on when outputs are active. ~~Times out 5 seconds after last output~~.

** Active only on when outputs are active. Resets at end of concert.

* Power - 12VDC Power supply from ~~3710~~ is on and 5V regulator is OK.

* Power - 12VDC Power supply from Power Supply Module is on and 5V regulator is OK.

** Should be as bright as power light on Power module.

* Test Mode - indicates self test is active. Inputs are ignored.

Line 56:

* Input - indicates that input data addressed to this panel, or

** Steady Blink if configuration switch error.

** Will not blink if incoming ~~note~~ is for this panel, but no module has been ~~addressed~~ for it.

** Will not blink if incoming activation data is for this panel, but no module has been installed for it.

* Output - indicates that this panel is sending status ~~out~~ to controller.

* Output - indicates that this panel is sending status back to the controller.

** Blinks brighter when set for low Baud.

* Interface 12V - DC-DC isolation converter is working - 12V available on 485 interface

* Interface 12V - DC-DC isolation converter is working - 12V available on 485 interface terminal

** Should be as bright as power light on Power module.

* Interface 5V - interface regulator is working (may be damaged by surges induced to data cable)

Line 65:

Power module

* Power - 12VDC Power supply is working and AC input within 100-240VAC

* Power - 12VDC Power supply is working and AC input is within 100-240VAC

* Active - indicates the high voltage relays are enabled. Indicates Interface ~~module~~ drive transistor is OK.

* Active - indicates the high voltage relays are enabled. Indicates Interface Module drive transistor is OK.

Output modules

@@ Line 47: / Line 47: @@
 Interface module
 * Active - indicates the high voltage relays are enabled. Indicated from logic before drive transistor.
-** Active only on when outputs are active. Times out 5 seconds after last output.
+** Active only on when outputs are active. Resets at end of concert.
-* Power - 12VDC Power supply from 3710 is on and 5V regulator is OK.
+* Power - 12VDC Power supply from Power Supply Module is on and 5V regulator is OK.
 ** Should be as bright as power light on Power module.
 * Test Mode - indicates self test is active. Inputs are ignored.
@@ Line 56: / Line 56: @@
 * Input - indicates that input data addressed to this panel, or
 ** Steady Blink if configuration switch error.
-** Will not blink if incoming note is for this panel, but no module has been addressed for it.
+** Will not blink if incoming activation data is for this panel, but no module has been installed for it.
-* Output - indicates that this panel is sending status out to controller.
+* Output - indicates that this panel is sending status back to the controller.
 ** Blinks brighter when set for low Baud.
-* Interface 12V - DC-DC isolation converter is working - 12V available on 485 interface
+* Interface 12V - DC-DC isolation converter is working - 12V available on 485 interface terminal
 ** Should be as bright as power light on Power module.
 * Interface 5V - interface regulator is working (may be damaged by surges induced to data cable)
@@ Line 65: / Line 65: @@
 Power module
-* Power - 12VDC Power supply is working and AC input within 100-240VAC
+* Power - 12VDC Power supply is working and AC input is within 100-240VAC
-* Active - indicates the high voltage relays are enabled. Indicates Interface module drive transistor is OK.
+* Active - indicates the high voltage relays are enabled. Indicates Interface Module drive transistor is OK.
 Output modules