(cleanup Performance)
(One intermediate revision by the same user not shown)
Line 64: Line 64:
** Qty 4 Premium horn drivers
** Qty 4 Premium horn drivers


Local electrician required to install two pair of AWG 12 THHN (if longer than 100 ft, larger wire may be required for full range) in conduit from amplifier location to the tower or steeple junction boxes. This system is not available for rooftop mounting.
Amplifier should be located close to speakers.
 
Local electrician required to install two pair of stranded AWG 12 THHN (if longer than 50 feet, larger wire may be required to meet full-range demand of 28A peak current) in conduit from amplifier location to the tower or steeple junction boxes. This system is not available for rooftop mounting.


=== '''inSpire™''' Performance ===
=== '''inSpire™''' Performance ===
Line 82: Line 84:
Amplifier should be installed within 50 feet of the speakers.
Amplifier should be installed within 50 feet of the speakers.


Local electrician required to install single short distance pair of AWG 12 THHN (minimum) in conduit from system location to the tower or steeple junction boxes. Additionally optional inside wiring to optional inside speaker location(s) (Performance 2500). This system is not available for rooftop mounting.
Local electrician required to install two pair of stranded AWG 12 THHN (if longer than 50 feet, larger wire may be required to meet full-range demand of 28A peak current) in conduit from amplifier location to the tower or steeple junction boxes. This system is not available for rooftop mounting. Additional wiring for optional inside speaker may also be installed.


=== '''inSpire™''' Ascent ===
=== '''inSpire™''' Ascent ===

Revision as of 21:40, 7 August 2019


In addition to these packages, we can customize a system for you with:

  • amplifier to connect existing working outdoor speakers
  • replacement drivers for existing horn speakers
  • installation and training
  • directional control
  • sanctuary sound
  • remote amplifier installation
  • control and augmentation of tower bells and chimes
  • tower clocks


inSpire™ Ultimate

  • Qty 2 InSpire amplifiers
    • Qty 1 inSpire DSP 1600W Amplifier
      • Two long throw directions from tower (independent levels) - four horns for each direction
      • Subwoofer upgrade channel (unused)
      • 400W inside monitoring amplifier channel (inside speaker included)
    • Qty 1 inSpire DSP 2500W Amplifier
      • Two full range output directions (independent levels) - two full range speakers for each direction
    • Custom engineered for each installation (tower survey not included)
      • Voicing for speaker combination below
      • Speaker protection programming
      • Time alignment compensation for speaker air columns and mounting position
  • Qty 4 inSpire Twelve full-range horn speakers
  • Qty 8 * Qty 8 Premium long-throw mid-range horns
    • Qty 8 Premium horn drivers
  • Qty 1 inSpire Sub 12 inch sub-woofer
  • Qty 1 8 inch two way inside monitor speaker

Local Electrician required to install five pair of AWG 12 THHN in conduit from system location to the tower or steeple junction boxes. This system is not available for rooftop mounting.

inSpire™ Professional

  • Qty 2 InSpire amplifiers
    • Qty 1 inSpire DSP 1600W Amplifier
      • Two long throw directions from tower (independent levels) - four horns for each direction
      • Future subwoofer upgrade channel (unused)
      • 400W inside monitoring amplifier channel (inside speakers optional)
    • Qty 1 inSpire DSP 2500W Amplifier
      • Two full range output directions (independent levels) - two full range speakers for each direction
    • Custom engineered for each installation (tower survey not included)
      • Voicing for speaker combination below
      • Speaker protection programming
      • Time alignment compensation for speaker air columns and mounting position
  • Qty 4 inSpire Twelve full-range horn speakers
  • Qty 8 * Qty 8 Premium long-throw mid-range horns
    • Qty 8 Premium horn drivers

Local electrician required to install four (or five for future subwoofer upgrade) pair of AWG 12 THHN in conduit from system location to the tower or steeple junction boxes. This system is not available for rooftop mounting.

inSpire™ Premium

  • Qty 1 inSpire DSP 2500W Amplifier
    • Custom engineered for each installation (tower survey not included)
      • Voicing for speaker combination below
      • Speaker protection programming
      • Time alignment compensation for speaker air columns and mounting position
  • Qty 4 inSpire Twelve full-range horn speakers
  • Qty 4 Premium long-throw mid-range horns
    • Qty 4 Premium horn drivers

Amplifier should be located close to speakers.

Local electrician required to install two pair of stranded AWG 12 THHN (if longer than 50 feet, larger wire may be required to meet full-range demand of 28A peak current) in conduit from amplifier location to the tower or steeple junction boxes. This system is not available for rooftop mounting.

inSpire™ Performance

  • Qty 1 inSpire DSP 2500W Amplifier
    • Custom engineered for each installation (tower survey not included)
      • Voicing for speaker system below
      • Speaker protection programming
  • Four inSpire Twelve full-range horn speakers in tower
    • All four tower speakers paralleled to a single pair wires run a short distance
    • All four paralleled to single 2-Ohm 1875W output (three paralleled output channels)
    • Inside speaker output D for up to 625W 70V (multi-drop for inside speakers with individual power settings)
  • Audio cable kit
    • Cables between carillon and amplifier for audio and control signals
    • SJTO pigtails for each speaker

Amplifier should be installed within 50 feet of the speakers.

Local electrician required to install two pair of stranded AWG 12 THHN (if longer than 50 feet, larger wire may be required to meet full-range demand of 28A peak current) in conduit from amplifier location to the tower or steeple junction boxes. This system is not available for rooftop mounting. Additional wiring for optional inside speaker may also be installed.

inSpire™ Ascent

  • Qty 1 inSpire DSP 1600W Amplifier
    • Custom engineered for each installation (tower survey not included)
      • Voicing for speaker combination below
      • Speaker protection programming
      • Time alignment compensation for speaker air columns and mounting position
  • Qty 1 inSpire Twelve full-range horn speaker
  • Qty 4 Premium long-throw mid-range horns
    • Qty 4 Premium horn drivers

Local electrician required to install two pair of AWG 12 THHN in conduit from system location to the tower or steeple junction boxes. Optional bracketing may be needed to mount speakers on roof (not a typical location for this system).

inSpire™ Outreach

  • Qty 1 inSpire DSP 1600W Amplifier
    • Custom engineered for each installation (tower survey not included)
      • Voicing for speaker combination below
      • Speaker protection programming
  • Qty 4 Premium long-throw horns
    • Qty 4 Premium horn drivers
  • Installation kit (does not include optional roof peak speaker bracket)
    • Qty 1 Junction box and cover
    • Qty 4 SJTO driver
    • Qty 4 Driver wiring pigtails with fork terminals attached
    • Brass set-screw wire nut kit
    • Screw Driver
  • 250 feet AWG 14-2 SJTO wire

Community Outreach

  • Qty 1 370W Amplifier
    • Audio cable kit
    • Amplifier settings pre-configured
  • Qty 4 Premium long-throw horns
    • Qty 4 Premium horn drivers
  • Installation kit (does not include optional roof peak speaker bracket)
    • Qty 1 Junction box and cover
    • Qty 4 SJTO driver
    • Qty 4 Driver wiring pigtails with fork terminals attached
    • Brass set-screw wire nut kit
    • Screw Driver
  • 250 feet AWG 14-2 SJTO wire

Value Outreach

  • An option for the Six-SS carillon.
  • 60W Amplifier module built-in to carillon
  • Pair of economy speakers
    • Qty 2 standard horns
    • Qty 2 standard horn drivers
  • Installation kit (does not include optional roof peak speaker bracket)
    • Qty 1 Junction box and cover
    • Qty 2 SJTO driver pigtails with fork terminals installed
    • Brass set-screw wire nut kit
    • Screw Driver
  • 250 feet AWG 14-2 SJTO wire