Difference between revisions of "Connect inSpire Ascent AX"

From Chime Master Help
Jump to: navigation, search
(inSpire Outreach AX)
(inSpire Ascent AX)
Line 9: Line 9:
 
== inSpire Ascent AX ==
 
== inSpire Ascent AX ==
 
* [[Sound_Packages#inSpire_Ascent|inSpire Ascent]] System specification
 
* [[Sound_Packages#inSpire_Ascent|inSpire Ascent]] System specification
* Download the illustrated PDF quick start guide
 
  
 
=== inSpire AX Ascent hookup instructions ===
 
=== inSpire AX Ascent hookup instructions ===
* [[Media:Hookup-inSpireAX-Ascent.pdf|Two tower cables without directional volume control]]
+
Download illustrated hookup diagrams:
** Amplifier preset AX16OA
+
;Directional outside zones (up to three long-throw horns each zone)
* [[Media:Hookup-inSpireAX-Ascent-Directional.pdf|Three tower cables for directional volume control]]
+
: [[Media:Hookup-inSpireAX-Ascent.pdf|Two tower cables without directional volume control]]
** Amplifier preset AX16OAD
+
: Use amplifier preset AX16OA
 +
;One single output zone (up to four long-throw horns)
 +
: [[Media:Hookup-inSpireAX-Ascent-Directional.pdf|Three tower cables for directional volume control]]
 +
: Use amplifier preset AX16OAD
  
 
The volume level settings in the AX virtual bell instrument can be found in the settings menu.
 
The volume level settings in the AX virtual bell instrument can be found in the settings menu.

Revision as of 07:16, 2 October 2019

inSpire Outreach AX

This package includes a digital amplifier with DSP tuned to drive four long-throw mid-high frequency horns. Additional amplifier outputs are provided for optional

  • Full-range tower speaker upgrade
  • Inside monitoring speaker

The amplifier is factory programmed with the same parameters as the Ascent package below so use the Ascent hookup instructions.

inSpire Ascent AX

inSpire AX Ascent hookup instructions

Download illustrated hookup diagrams:

Directional outside zones (up to three long-throw horns each zone)
Two tower cables without directional volume control
Use amplifier preset AX16OA
One single output zone (up to four long-throw horns)
Three tower cables for directional volume control
Use amplifier preset AX16OAD

The volume level settings in the AX virtual bell instrument can be found in the settings menu.

  • Use Zone A level for the loud side
  • Use Zone B level for the quieter side
  • Use Monitor 1 level for the optional inside speaker if connected

Tower speaker connections

  1. Secure speakers according to instructions enclosed in packing using supplied hardware as required.
  2. Connect supplied pigtails to horn drivers before screwing the drivers into the horns. Note that low impedance drivers are normally supplied with two terminal screws. Do not move the screws to non-functioning 70V terminals.
  3. Bring the pigtails from each horn to the supplied junction box. Bring the mid-range channel supply cable from the amplifier (Channels A and B outputs are paralleled with the supplied jumpers) into the junction box. Connect all five of the white wires together, then all of the black wires together using two of the larger brass set-screw wire-nuts and covers. Orient the threaded part of the brass insert toward the wire insulation. Tighten the set-screw and trim excess wire from the end of the insert before screwing on the wire-nut cover.
  4. Remove the 70V Jumper on from the terminal on the full-range horn.
  5. Connect the full-range channel supply cable from the amplifier (Channel C) to the full-range horn. Connect the white wire to the COM terminal, and the black wire to the 4 Ohm voice coil terminal.