Network setup AX: Difference between revisions

Line 24:

The AX line was designed to be connected to the internet, but if none is available at your facility, you can still use the [[Remote_AX|remote control]].

* While the Chime Master AX carillon is powered off, plug in the included wireless antenna into the top right USB port on the back, then restart the unit.

* From the home page, choose Settings then Network. At the top, you can view if you are connected via an Ethernet cable or a wireless network~~. If your unit is connected to WiFi, first tap Disconnect. If this is not updated after several minutes, exit the page and go through~~ the ~~steps again. Recycling the power may also help successfully disconnect~~.

* From the home page, choose Settings then Network. At the top, you can view if you are connected via an Ethernet cable or a wireless network (network address beside the appropriate IP label).

* ~~Once you are successfully disconnected, you can turn on~~ the Access Point switch in the lower left corner of the screen. ~~It may take several minutes for the system to accurately display~~ the Access Point ~~status~~.

* Tap the Access Point switch in the lower left corner of the screen. When the Access Point switch is gold and an IP address appears beside ''Wireless IP'' you can exit the Network setup page and proceed.

* Return to the home page of the ~~Platinum AX then choose~~ Remote.

* Return to the home page, then tap the Remote button.

* After entering your PIN, the system will check its network connection status. You will be asked to connect your smart phone or other device to a password protected CMS WiFi. On the ~~next screen of~~ the carillon, ~~you will~~ scan the ~~new~~ QR code with your phone’s camera or QR reader. Tap the link which is provided from the QR code to open the Access Point Remote in your phone’s browser.

* After entering your PIN, the system will check its network connection status. You will be asked to connect your smart phone or other device to a password protected CMS WiFi. The SSID and Password will appear above the QR Code. After connecting your phone to the carillon's network, scan the QR code with your phone’s camera or QR reader. Tap the link which is provided from the QR code to open the Access Point Remote in your phone’s browser.

;Note

:The QR code information when using the ringing system's network is different that the one provided when the system is on the Internet. If later you connect the system to the Internet, you will need to scan the Chime Center remote code as described in the previous section.

== Security ==

@@ Line 24: / Line 24: @@
 The AX line was designed to be connected to the internet, but if none is available at your facility, you can still use the [[Remote_AX|remote control]].
 * While the Chime Master AX carillon is powered off, plug in the included wireless antenna into the top right USB port on the back, then restart the unit.
-* From the home page, choose Settings then Network. At the top, you can view if you are connected via an Ethernet cable or a wireless network. If your unit is connected to WiFi, first tap Disconnect. If this is not updated after several minutes, exit the page and go through the steps again. Recycling the power may also help successfully disconnect.
+* From the home page, choose Settings then Network. At the top, you can view if you are connected via an Ethernet cable or a wireless network (network address beside the appropriate IP label).
-* Once you are successfully disconnected, you can turn on the Access Point switch in the lower left corner of the screen. It may take several minutes for the system to accurately display the Access Point status.
+* Tap the Access Point switch in the lower left corner of the screen. When the Access Point switch is gold and an IP address appears beside ''Wireless IP'' you can exit the Network setup page and proceed.
-* Return to the home page of the Platinum AX then choose Remote.
+* Return to the home page, then tap the Remote button.
-* After entering your PIN, the system will check its network connection status. You will be asked to connect your smart phone or other device to a password protected CMS WiFi. On the next screen of the carillon, you will scan the new QR code with your phone’s camera or QR reader. Tap the link which is provided from the QR code to open the Access Point Remote in your phone’s browser.
+* After entering your PIN, the system will check its network connection status. You will be asked to connect your smart phone or other device to a password protected CMS WiFi. The SSID and Password will appear above the QR Code. After connecting your phone to the carillon's network, scan the QR code with your phone’s camera or QR reader. Tap the link which is provided from the QR code to open the Access Point Remote in your phone’s browser.
+;Note
+:The QR code information when using the ringing system's network is different that the one provided when the system is on the Internet. If later you connect the system to the Internet, you will need to scan the Chime Center remote code as described in the previous section.
 == Security ==