Date and Time AX: Difference between revisions

Latest revision as of 17:09, 22 August 2022

Help » Operating manuals » AX Table of Contents
← Settings screen Next section →

During normal operation, the system is assumed to be connected to a network with Internet access. Time is normally automatically kept synchronized and updated when the system is powered on. In the case where Internet time is not available, the system relies on a built-in accurate clock. This clock will run for a reasonable amount of time when power is disconnected, and the backup power source will recharge when the system is plugged in.

Part of the setup process involves selecting your time zone and enabling or disabling Daylight time adjustments.

Automatic Daylight Savings Time: If the switch has a check-mark, daylight time will auto-adjust with no user intervention.

If Internet is unavailable

You only have to manually set and occasionally correct the time if Internet time servers are not available. Daylight time adjustments will continue to occur automatically if enabled.

Automatic Clock Sync: The switch caption will warn (even if enabled), "No Internet Connection - Clock will not sync."

To set the time

Turn off Automatic Clock Sync and a button will appear, Manually Set Date & Time to the right of the switch. Tap this button.
Select the current month and year using the arrows and pull-downs at the top of the calendar screen.
Select the current date on the calendar.
Select the current (or upcoming) hour on the clock, tap the digital minutes at the top of the clock and select the next minute.
Observe an accurate clock. When it shows the time you have set and the seconds are zero, tap the button at the bottom of the screen, Synchronize to :00 seconds.
Tap the lower right Save button. The screen may go dark if you had to set the clock forward very far. Tap anywhere on the screen to resume.

Early firmware manual settings

If you do not have an Internet connection and your firmware version is older than 1.4.12 (on Settings - About menu), use the following steps to set the time in the event that the system has been powered off long enough to lose the correct time. Early firmware allowed the date advance only a few months at a time.

Plug in the system to AC power and allow an hour for the clock backup circuit to recharge before attempting to log in to adjust the clock. After an hour of charging, if the AX logo does not switch to the clock screen, hold the Gold power button to shut the system down and restart it after the button becomes solid blue.

If the system never restarts to get past the AX logo, you should try connecting the system to a wired Ethernet Internet connection.

Steps

Login to the system, tap Settings and then tap Date & Time.
In Date & Time menu, tap the button to Manually Set Date & Time then these steps:
Tap the right arrow on the calendar to advance months no more than five ahead (even if we are not there yet).
Tap the date 1 on the last available month, or the correct date if you have reached the correct month.
Set the time to the current time. The system will log you out and the screen will go blank.
Log in and repeat the last instructions until you get to the current date and time.

If an invalid season is displayed on the clock screen after you have corrected the time, allow several minutes for the database to make the correction.

← Settings screen Next section →

@@ Line 1: / Line 1: @@
+<span class="crumbs"><div style="font-size:84%">
+'''[[Chime_Master_Help|Help]] &raquo;  [[Operating manuals]] &raquo; [[:Category:AX_Manual|AX Table of Contents]]'''<br/>
+'''  &nbsp;&nbsp;&nbsp;&nbsp;[[Settings_screen_AX|&larr; Settings screen]] &nbsp;&nbsp;&nbsp;&nbsp; [[User_profile_setup_AX|Next section &rarr;]] '''
+</div></span>
 During normal operation, the system is assumed to be connected to a network with Internet access. Time is normally automatically kept synchronized and updated when the system is powered on. In the case where Internet time is not available, the system relies on a built-in accurate clock. This clock will run for a reasonable amount of time when power is disconnected, and the backup power source will recharge when the system is plugged in.
 Part of the setup process involves selecting your time zone and enabling or disabling Daylight time adjustments.
+[[File:Date&Time.jpg|600px]]
 ;Automatic Daylight Savings Time
@@ Line 8: / Line 15: @@
 == If Internet is unavailable ==
-You only have to manually set and occasionally correct the time if Internet time servers are not available. Daylight time adjustments will occur automatically if enabled.
+You only have to manually set and occasionally correct the time if Internet time servers are not available. Daylight time adjustments will continue to occur automatically if enabled.
 ;Automatic Clock Sync
-:The switch caption will warn (even if enabled)
+:The switch caption will warn (even if enabled), "No Internet Connection - Clock will not sync."
-:  No Internet Connection - Clock will not sync
+;To set the time
+#Turn off Automatic Clock Sync and a button will appear, '''Manually Set Date & Time''' to the right of the switch. Tap this button.
+#Select the current month and year using the arrows and pull-downs at the top of the calendar screen.
+#Select the current date on the calendar.
+#Select the current (or upcoming) hour on the clock, tap the digital minutes at the top of the clock and select the next minute.
+#Observe an accurate clock. When it shows the time you have set and the seconds are zero, tap the button at the bottom of the screen, '''Synchronize to :00 seconds'''.
+#Tap the lower right Save button. The screen may go dark if you had to set the clock forward very far. Tap anywhere on the screen to resume.
+=== Early firmware manual settings ===
+If you do not have an Internet connection and your firmware version is older than 1.4.12 (on Settings - About menu), use the following steps to set the time in the event that the system has been powered off long enough to lose the correct time. Early firmware allowed the date advance only a few months at a time.
-Turn off Automatic Clock Sync and a button will appear, '''Manually Set Date & Time''' to the right of the switch. Tap this button.
+Plug in the system to AC power and '''allow an hour''' for the clock backup circuit to recharge before attempting to log in to adjust the clock. After an hour of charging, if the AX logo does not switch to the clock screen, hold the Gold power button to shut the system down and restart it after the button becomes solid blue.
-Select the current month and year using the arrows and pull-downs at the top of the calendar screen.
+* If the system never restarts to get past the AX logo, you should try connecting the system to a wired Ethernet Internet connection.
-Select the current date on the calendar.
+Steps
+# Login to the system, tap '''Settings''' and then tap '''Date & Time.'''
+# In Date & Time menu, tap the button to '''Manually Set Date & Time''' then these steps:
+# Tap the right arrow on the calendar to advance months no more than five ahead (even if we are not there yet).
+# Tap the date ''1'' on the last available month, or the correct date if you have reached the correct month.
+# Set the time to the current time. The system will log you out and the screen will go blank.
+# Log in and repeat the last instructions until you get to the current date and time.
-Select the current (or upcoming) hour on the clock, tap the digital minutes at the top of the clock and select the next minute.
+If an invalid season is displayed on the clock screen after you have corrected the time, allow several minutes for the database to make the correction.
-Observe an accurate clock. When it shows the time you have set and the seconds are zero, tap the button at the bottom of the screen, '''Synchronize to :00 seconds'''.
+<span class="crumbs"><div style="font-size:84%">
+'''  &nbsp;&nbsp;&nbsp;&nbsp;[[Settings_screen_AX|&larr; Settings screen]] &nbsp;&nbsp;&nbsp;&nbsp; [[User_profile_setup_AX|Next section &rarr;]] '''
+</div></span>
-[[Category:Manual AX]]
+[[Category:AX Manual]]