Set system clock setup menu - Revision history

Daveallen: LX Backup circuit recharge

2021-05-19T16:43:47Z

LX Backup circuit recharge

← Older revision		Revision as of 16:43, 19 May 2021
Line 4:		Line 4:

	Temperature compensated crystal clock circuitry gives the clock accuracy greater than +/- two minutes per year. Periodic checks and settings of the clock may be necessary to insure accurate operation of the system. The clock is factory set to your local time before shipment and should not require setting at the time of installation.		Temperature compensated crystal clock circuitry gives the clock accuracy greater than +/- two minutes per year. Periodic checks and settings of the clock may be necessary to insure accurate operation of the system. The clock is factory set to your local time before shipment and should not require setting at the time of installation.

			LX Ringing systems: If the system has not been powered for some time, the backup capacitor will need to charge before you can set the clock. Allow 20-30 minutes after powering the system for charging.

	== Open the Menu ==		== Open the Menu ==

Daveallen: rm msuite ref

2021-05-19T16:32:34Z

rm msuite ref

← Older revision		Revision as of 16:32, 19 May 2021
Line 4:		Line 4:

	Temperature compensated crystal clock circuitry gives the clock accuracy greater than +/- two minutes per year. Periodic checks and settings of the clock may be necessary to insure accurate operation of the system. The clock is factory set to your local time before shipment and should not require setting at the time of installation.		Temperature compensated crystal clock circuitry gives the clock accuracy greater than +/- two minutes per year. Periodic checks and settings of the clock may be necessary to insure accurate operation of the system. The clock is factory set to your local time before shipment and should not require setting at the time of installation.

	~~You can also synchronize the carillon system time clock to internet time (or your own local NTP server) using a Windows PC with our [[Install_Management_Suite\|downloadable Management Suite]].~~

	== Open the Menu ==		== Open the Menu ==

Daveallen at 22:28, 8 February 2018

2018-02-08T22:28:51Z

← Older revision		Revision as of 22:28, 8 February 2018
Line 5:		Line 5:
	Temperature compensated crystal clock circuitry gives the clock accuracy greater than +/- two minutes per year. Periodic checks and settings of the clock may be necessary to insure accurate operation of the system. The clock is factory set to your local time before shipment and should not require setting at the time of installation.		Temperature compensated crystal clock circuitry gives the clock accuracy greater than +/- two minutes per year. Periodic checks and settings of the clock may be necessary to insure accurate operation of the system. The clock is factory set to your local time before shipment and should not require setting at the time of installation.

	You can also synchronize the carillon system time clock to internet time (or your own local NTP server) using a Windows PC with our [Install_Management_Suite\|downloadable Management Suite]].		You can also synchronize the carillon system time clock to internet time (or your own local NTP server) using a Windows PC with our [[Install_Management_Suite\|downloadable Management Suite]].

	== Open the Menu ==		== Open the Menu ==

Daveallen at 21:56, 30 December 2016

2016-12-30T21:56:29Z

← Older revision		Revision as of 21:56, 30 December 2016
Line 1:		Line 1:
			<div style="font-size:84%">'''[[Chime_Master_Help\|Help]] > [[Operating manuals]] '''</div>

	This menu is found on all Chime Master bell ringing equipment with a two line display and sixteen button keypad. It is used to make corrections to the time clock.		This menu is found on all Chime Master bell ringing equipment with a two line display and sixteen button keypad. It is used to make corrections to the time clock.

Line 5:		Line 7:
	You can also synchronize the carillon system time clock to internet time (or your own local NTP server) using a Windows PC with our [Install_Management_Suite\|downloadable Management Suite]].		You can also synchronize the carillon system time clock to internet time (or your own local NTP server) using a Windows PC with our [Install_Management_Suite\|downloadable Management Suite]].

	== Open the ~~menu~~ ==		== Open the Menu ==

	Open the Time strike/auto level setup menu by pressing the front panel green ''Enter'' button so that you read ''Main Menu'' on the top line of the display. Press any gray cursor button until the flashing lower line reads ''System Setup Menu'' then press the ''Enter'' button again.		Open the Time strike/auto level setup menu by pressing the front panel green ''Enter'' button so that you read ''Main Menu'' on the top line of the display. Press any gray cursor button until the flashing lower line reads ''System Setup Menu'' then press the ''Enter'' button again.
Line 18:		Line 20:
	The minute will be blinking. Use the cursor left and right buttons to move around the display (and cause other elements to blink). Change the settings for the blinking element using the cursor up and down buttons.		The minute will be blinking. Use the cursor left and right buttons to move around the display (and cause other elements to blink). Change the settings for the blinking element using the cursor up and down buttons.

	== Set the ~~time~~ ==		== Set the Time ==

	Use the cursor right button to make ''Set Time'' blink, then press the green ''Enter'' button when you want to start the clock from the selected time.		Use the cursor right button to make ''Set Time'' blink, then press the green ''Enter'' button when you want to start the clock from the selected time.
Line 24:		Line 26:
	The display will read ''Setting real time clock'' while it restarts the clock.		The display will read ''Setting real time clock'' while it restarts the clock.

	=== Tower ~~clock movement hand position~~ ===		=== Tower Clock Movement Hand Position ===

	This section only applies to systems that are controlling an external clock movement.		This section only applies to systems that are controlling an external clock movement.
Line 39:		Line 41:
	Press ''Enter'' to restart the tower clock. It should wait or catch up to the current time.		Press ''Enter'' to restart the tower clock. It should wait or catch up to the current time.

	== Exit the ~~menu~~ ==		== Exit the Menu ==

	After you have finished setting the time, press the red ''Cancel'' button to return to the automatic standby mode.		After you have finished setting the time, press the red ''Cancel'' button to return to the automatic standby mode.

	[[category:manual]]		[[category:manual]]

Daveallen: /* Set the time */

2016-12-28T22:45:24Z

Set the time

← Older revision		Revision as of 22:45, 28 December 2016
Line 21:		Line 21:

	Use the cursor right button to make ''Set Time'' blink, then press the green ''Enter'' button when you want to start the clock from the selected time.		Use the cursor right button to make ''Set Time'' blink, then press the green ''Enter'' button when you want to start the clock from the selected time.

			The display will read ''Setting real time clock'' while it restarts the clock.

	=== Tower clock movement hand position ===		=== Tower clock movement hand position ===

Daveallen: created

2016-12-28T22:44:22Z

created

New page

This menu is found on all Chime Master bell ringing equipment with a two line display and sixteen button keypad. It is used to make corrections to the time clock.

Temperature compensated crystal clock circuitry gives the clock accuracy greater than +/- two minutes per year. Periodic checks and settings of the clock may be necessary to insure accurate operation of the system. The clock is factory set to your local time before shipment and should not require setting at the time of installation.

You can also synchronize the carillon system time clock to internet time (or your own local NTP server) using a Windows PC with our [Install_Management_Suite|downloadable Management Suite]].

== Open the menu ==

Open the Time strike/auto level setup menu by pressing the front panel green ''Enter'' button so that you read ''Main Menu'' on the top line of the display. Press any gray cursor button until the flashing lower line reads ''System Setup Menu'' then press the ''Enter'' button again.

The top line should now say ''System Setup Menu'' and you may press any gray cursor button until the lower line is blinking ''Set System Clock''. One more press of the ''Enter'' button will get us there.

When you open this menu, the display will read:

5:35 PM WED 12-28
Year=2016 Set Time

The minute will be blinking. Use the cursor left and right buttons to move around the display (and cause other elements to blink). Change the settings for the blinking element using the cursor up and down buttons.

== Set the time ==

Use the cursor right button to make ''Set Time'' blink, then press the green ''Enter'' button when you want to start the clock from the selected time.

=== Tower clock movement hand position ===

This section only applies to systems that are controlling an external clock movement.

If you entered the menu to correct for slow or fast clock movements in the outside clocks, you can press the red ''Cancel'' button to skip updating the system time.

After the system time has been set, the display will read:

Tower clock dial
hands indicate: 5:33

Use the cursor up and down to change the settings to match the clock dial. The motor will be turned off while in this mode to give you time to read it.

Press ''Enter'' to restart the tower clock. It should wait or catch up to the current time.

== Exit the menu ==

After you have finished setting the time, press the red ''Cancel'' button to return to the automatic standby mode.

[[category:manual]]