MagForce motor system installation - Revision history

Daveallen: /* Programming Procedure */

2024-06-19T18:49:11Z

Programming Procedure

← Older revision		Revision as of 18:49, 19 June 2024
Line 94:		Line 94:
	The MagForce control panel for single phase will have a capacitor on the output between outputs ''U'' and ''V''. If the motor is sized to require an overload protector, the ''L1'' connection to the triac input will be routed in a serpentine fashion through the three overload circuits. This is required to prevent trips caused by the missing phase detection.		The MagForce control panel for single phase will have a capacitor on the output between outputs ''U'' and ''V''. If the motor is sized to require an overload protector, the ''L1'' connection to the triac input will be routed in a serpentine fashion through the three overload circuits. This is required to prevent trips caused by the missing phase detection.

	== Programming Procedure ==		== Programming Procedure (PERIOD proximity) ==
	IMPORTANT:		IMPORTANT:
	* If a rotary encoder is installed on the headstock spindles (chip on control board has a label marked '''SENSOR''')		* If a rotary encoder is installed on the headstock spindles (chip on control board has a label marked '''SENSOR''')

Daveallen: make clear this setup method is for PERIOD proximity sensors

2024-06-13T16:06:30Z

make clear this setup method is for PERIOD proximity sensors

← Older revision		Revision as of 16:06, 13 June 2024
Line 95:		Line 95:

	== Programming Procedure ==		== Programming Procedure ==
	~~[[File~~:~~Intelliswing-terminal.jpg\|frameless\|right]]~~		IMPORTANT:
	The intelliSwing motor control system must be programmed with the bell at the time of installation. A special hand-held terminal is required for this setup and is available on loan from Chime Master with a deposit.

	* If the bell has a proximity sensor for position feedback (chip on control board has a label marked '''PERIOD''')
	** Then continue to use this programming procedure.
	* If a rotary encoder is installed on the headstock spindles (chip on control board has a label marked '''SENSOR''')		* If a rotary encoder is installed on the headstock spindles (chip on control board has a label marked '''SENSOR''')
	** Then go to the '''[[IntelliSwing_rotary_sensor_setup#Programming_the_controller\|rotary sensor programming procedure]]''' and use the parameter options there for MagForce Linear motors.		** Then go to the '''[[IntelliSwing_rotary_sensor_setup#Programming_the_controller\|rotary sensor programming procedure]]''' and use the parameter options there for MagForce Linear motors.
			* If the bell with a proximity sensor is being serviced (chip on control board has a label marked '''PERIOD''')
			** Then continue to use this programming procedure

	=== Using the Terminal ===		=== Using the Terminal ===
	~~[[File:Intelliswing-termcon.jpg\|frameless\|right]]~~
	~~Connect the programming terminal and turn on panel power.~~

	The right cursor button will take you through the settings for each bell in the system. From the status window, shown below, you can cursor left to select another bell. To change settings you can increment/decrement using the up and down arrow buttons, or input the value with the numeric buttons and save it with the EXE button.		The right cursor button will take you through the settings for each bell in the system. From the status window, shown below, you can cursor left to select another bell. To change settings you can increment/decrement using the up and down arrow buttons, or input the value with the numeric buttons and save it with the EXE button.

Daveallen: /* Mounting the stationary motor brick */

2024-06-13T16:01:03Z

Mounting the stationary motor brick

← Older revision		Revision as of 16:01, 13 June 2024
Line 16:		Line 16:

	Motors can be mounted above the bell (at the same radius from the pivot point) if the weight of the reaction plate is taken into consideration when designing the head stock crank depth. This will also slow the ringing tempo. Do not mount the motors above the pivot on existing cranked head stocks, the bell will not ring properly.		Motors can be mounted above the bell (at the same radius from the pivot point) if the weight of the reaction plate is taken into consideration when designing the head stock crank depth. This will also slow the ringing tempo. Do not mount the motors above the pivot on existing cranked head stocks, the bell will not ring properly.

			The motor should be mounted to a 1/4 to 3/8 inch aluminum plate when possible to serve as a heat sink. The plate can then be spaced out from the frame with threaded rod for positioning toward the reaction plate.

	The motor induction housing should be painted with a polyurethane coating for UV resistance when used outside, and can be painted with the tower to match.		The motor induction housing should be painted with a polyurethane coating for UV resistance when used outside, and can be painted with the tower to match.

Daveallen: /* Low current feedback connections */

2024-06-13T14:10:07Z

Low current feedback connections

@@ Line 28: / Line 28: @@
 The motor control circuit needs some motion feedback from the bell to determine that it is swinging properly. We offer two types of feedback devices to accomplish this. The wiring requirements are the same for both. Four conductors of a telco or CAT5 cable usually suffice for this low current 12V signaling.
-=== Proximity sensor (standard) ===
+=== Precision rotary motion sensor (standard) ===
 A three wire (60 inch cable) proximity sensor provides output when a bolt head or metal flag is about 1/4 inch away. Typically, a bolt is mounted to protrude from the bell wheel or head stock assembly. A stainless steel sheet metal flag is also supplied that can be mounted with dual adhesive foam tape or epoxy to the wheel or head stock.
@@ Line 42: / Line 57: @@
 If you use a cable with other colors to extend these wires, make note of the colors you splice together, so the connections to the control computer circuit board are correct.
 == System electrical connections ==

Rickwhite: Overload Single Phase wiring

2023-08-10T14:25:29Z

Overload Single Phase wiring

← Older revision		Revision as of 14:25, 10 August 2023
Line 88:		Line 88:

	==== Single phase MagForce panel ====		==== Single phase MagForce panel ====
	The MagForce control panel for single phase will have a capacitor on the output between outputs ''U'' and ''V''. If the motor is sized to require an overload protector, the ''W'' connection will be routed in a serpentine fashion through the three ~~disconnect~~ circuits. This is required to prevent trips caused by the missing phase detection.		The MagForce control panel for single phase will have a capacitor on the output between outputs ''U'' and ''V''. If the motor is sized to require an overload protector, the ''L1'' connection to the triac input will be routed in a serpentine fashion through the three overload circuits. This is required to prevent trips caused by the missing phase detection.

	== Programming Procedure ==		== Programming Procedure ==

Rickwhite: /* Programming Procedure */

2022-08-22T15:09:01Z

Programming Procedure

← Older revision		Revision as of 15:09, 22 August 2022
Line 95:		Line 95:

	* If the bell has a proximity sensor for position feedback (chip on control board has a label marked '''PERIOD''')		* If the bell has a proximity sensor for position feedback (chip on control board has a label marked '''PERIOD''')
	** ~~Continue~~ to use this programming procedure		** Then continue to use this programming procedure.
	* If a rotary encoder is installed on the headstock spindles (chip on control board has a label marked '''SENSOR''')		* If a rotary encoder is installed on the headstock spindles (chip on control board has a label marked '''SENSOR''')
	** Go to the '''[[IntelliSwing_rotary_sensor_setup#Programming_the_controller\|rotary sensor programming procedure]]'''		** Then go to the '''[[IntelliSwing_rotary_sensor_setup#Programming_the_controller\|rotary sensor programming procedure]]''' and use the parameter options there for MagForce Linear motors.

	=== Using the Terminal ===		=== Using the Terminal ===

Rickwhite: /* Programming Procedure */

2022-08-22T15:07:49Z

Programming Procedure

← Older revision		Revision as of 15:07, 22 August 2022
Line 97:		Line 97:
	** Continue to use this programming procedure		** Continue to use this programming procedure
	* If a rotary encoder is installed on the headstock spindles (chip on control board has a label marked '''SENSOR''')		* If a rotary encoder is installed on the headstock spindles (chip on control board has a label marked '''SENSOR''')
	** Go to the '''[[IntelliSwing_rotary_sensor_setup#Programming_the_controller\|rotary ~~motor~~ programming procedure]]'''		** Go to the '''[[IntelliSwing_rotary_sensor_setup#Programming_the_controller\|rotary sensor programming procedure]]'''

	=== Using the Terminal ===		=== Using the Terminal ===

Rickwhite: /* Programming Procedure */

2022-08-22T15:07:17Z

Programming Procedure

← Older revision		Revision as of 15:07, 22 August 2022
Line 94:		Line 94:
	The intelliSwing motor control system must be programmed with the bell at the time of installation. A special hand-held terminal is required for this setup and is available on loan from Chime Master with a deposit.		The intelliSwing motor control system must be programmed with the bell at the time of installation. A special hand-held terminal is required for this setup and is available on loan from Chime Master with a deposit.

	* If the bell has a proximity sensor for position feedback (chip on control board has a label marked '''PERIOD'''		* If the bell has a proximity sensor for position feedback (chip on control board has a label marked '''PERIOD''')
	** Continue to use this programming procedure		** Continue to use this programming procedure
	* If a rotary encoder is installed on the headstock spindles (chip on control board has a label marked '''SENSOR'''		* If a rotary encoder is installed on the headstock spindles (chip on control board has a label marked '''SENSOR''')
	** Go to the '''[[IntelliSwing_rotary_sensor_setup#Programming_the_controller\|rotary motor programming procedure]]'''		** Go to the '''[[IntelliSwing_rotary_sensor_setup#Programming_the_controller\|rotary motor programming procedure]]'''

Rickwhite: /* Programming Procedure */

2022-08-22T15:06:41Z

Programming Procedure

← Older revision		Revision as of 15:06, 22 August 2022
Line 94:		Line 94:
	The intelliSwing motor control system must be programmed with the bell at the time of installation. A special hand-held terminal is required for this setup and is available on loan from Chime Master with a deposit.		The intelliSwing motor control system must be programmed with the bell at the time of installation. A special hand-held terminal is required for this setup and is available on loan from Chime Master with a deposit.

	* ~~Continue below if~~ the bell has a proximity sensor for position feedback		* If the bell has a proximity sensor for position feedback (chip on control board has a label marked '''PERIOD'''
	* If a rotary encoder is installed on the headstock spindles		** Continue to use this programming procedure
	** Write down that the setting for '''Transmission''' is '''~~22.8~~'''		* If a rotary encoder is installed on the headstock spindles (chip on control board has a label marked '''SENSOR'''
	** Go to the '''[[~~IntelliSwing_Rotary_installation~~#Programming_the_controller\|rotary motor programming procedure]]'''		** Go to the '''[[IntelliSwing_rotary_sensor_setup#Programming_the_controller\|rotary motor programming procedure]]'''

	=== Using the Terminal ===		=== Using the Terminal ===

Daveallen: print no crumbs

2022-08-10T16:40:08Z

print no crumbs

← Older revision		Revision as of 16:40, 10 August 2022
Line 1:		Line 1:
	<div style="font-size:84%">'''[http://www.ChimeMaster.com Home] > [[Chime_Master_Help\|Help]] > [[Installation_documentation\|Installation]] '''</div><br />		<span class="crumbs"><div style="font-size:84%">'''[http://www.ChimeMaster.com Home] > [[Chime_Master_Help\|Help]] > [[Installation_documentation\|Installation]] '''</div><br /></span>
	[http://www.chimemaster.com/swinging-motors Chime Master intelliSwing MagForce™] swinging bell systems feature a unique touch-less, friction-less and nearly silent motor technology. A stationary drive module induces electro-motive eddy-current forces into a reactor plate mounted to the free swinging bell assembly. A wall mounted motion control panel intelligently experiments and quickly learns the unique physical properties of your bell then carefully manages the energy required for accurate ringing.		[http://www.chimemaster.com/swinging-motors Chime Master intelliSwing MagForce™] swinging bell systems feature a unique touch-less, friction-less and nearly silent motor technology. A stationary drive module induces electro-motive eddy-current forces into a reactor plate mounted to the free swinging bell assembly. A wall mounted motion control panel intelligently experiments and quickly learns the unique physical properties of your bell then carefully manages the energy required for accurate ringing.